VMX88 Advanced Digital Audio Dynamic Processing Management System (Dante)
The VMX88 provides the advantages and experience of our on-site sound filter and dynamic algorithms for fixed installation products. Each of the 8 analog input channels features an adjustable knee high-level compressor and a 24dB/OCT high-pass filter, 8 selectable types of EQ, 2-stage dynamic equalization (DEQ), and adjustable delay of up to 1.3 seconds. The full matrix signal mixer allows not only analog inputs but also the mixing of 8 Dante network audio input channels to any output channel, providing flexibility in system design by routing audio channels from multiple stages of the audio chain to the 8 channels of Dante network output. There are 8 analog outputs, each equipped with 48dB/OCT high-pass and low-pass filters, 16 selectable types of EQ, adjustable delay of up to 1.3 seconds, and a state-of-the-art high-performance two-stage Predictive eXcursion Limiter (PXL) limiter design, aimed at providing optimal drive protection and minimal distortion. All analog audio interfaces use 3-pin 5.08mm pitch Phoenix connectors, with 4 GPI connections that allow customizable operational configurations (such as fire alarm mute and preset recall), and up to 30 presets can be stored and recalled, allowing for the selection of input, matrix, and output combinations. Our D-Net based Ethernet control software for PC, Mac, and iPad not only allows you to control all devices on the network but also provides flexible storage of preset memories and system configurations (including in offline mode). The VMX88 is also fully compatible with our VR1 PoE remote control panel for simple and flexible user control, and can be controlled via simple Ethernet control protocols through third-party systems (such as Crestron, AMX, etc.).
- Product Application: Bar, Party K room, etc.
- Product Description
-
VMX88 Technical Details
Analog Inputs: 8
Electronic Balance, Phoenix Connector
Common Mode Rejection Ratio: >60dB@1kHz
Maximum Level: >20dbu
Signal-to-Noise Ratio SNR: 119dB 'A' weighted
Input Impedance: 10kΩ Balanced
Analog Output - 8 Channels
Electronic Balance, Phoenix Connector
Maximum Level: >20dbu
Signal-to-Noise Ratio SNR: 122dB 'A' weighted
Source Impedance: <60Ω
Performance Parameters
Frequency Response (12Hz to 32kHz): +/-0.2dB
Dynamic Range: >119dB A-weighted (Analog In to Analog Out)
Total Harmonic Distortion + Noise (+19dB @ 1kHz): 0.00029%
Latency: 0.427ms (Input to Output, Analog)
Processor Main Functions [96kHz]
Input Gain (per channel): -30 to +15dB, 0.1dB steps, Mute, +/- Polarity (+/- Phase)
Input Delay (per channel): 0 to 1.3s, minimum increment 1us (<10ms), minimum increment 0.01ms (>10ms and <100ms), minimum increment 0.1ms (>100ms and <1000ms), minimum increment 0.001s (>1s).
Input Compressor (per channel): Threshold (-30 to +22 dBu), Attack Time, Release Time, Compression Ratio, Soft Knee Adjustment
Input Multiple Types of Selectable EQ (per channel): 8 – Parametric, Low Shelf, High Shelf, Band-pass, Notch, Phase, Allpass, Low Pass Filter, High Pass Filter.
Input Dynamic Equalization DEQ (per channel): 2 Bands – Filter Type (parametric/low shelf/high shelf), Dynamic Processing Mode (boost/cut above/below), Threshold, Dynamic Ratio, Attack Time, Release Time
Input High Pass Filter (per channel): Maximum 24dB/OCT Slope (Benson / Butterworth / Bessel / Linkwitz-Riley)
Input to Output Routing: Full Matrix Mixing, including all local inputs to Dante outputs and Dante inputs to local outputs
Output Multiple Types of Selectable EQ (per channel): 16 – Parametric, Low Shelf, High Shelf, Band-pass, Notch, Phase, Allpass, Low Pass Filter, High Pass Filter.
Output High Pass and Low Pass Filters (per channel): Maximum 48dB/OCT Slope (Benson/Butterworth/Bessel/Linkwitz Riley)
Output Gain (per channel): -30 to +15dB, 0.1dB steps, Mute, +/- Polarity (+/- Phase)
Output Delay (per channel): 0 to 1.3s, minimum increment 1us (<10ms), minimum increment 0.01ms (>10ms and <100ms), minimum increment 0.1ms (>100ms and <1000ms), minimum increment 0.001s (>1s).
Output (PXL) Limiter (per channel): Threshold (-50 to +22 dBu), Attack Time, Release Time, Auto Attack/Release Time Options
Presets: Up to 30 (increased to 100: D-NET version updated to 2.0.3 or higher and updated with the latest firmware)
Network Audio: 8in/8out Dante Channel Connector on Dual Redundant RJ45
Communication Interface: 100Mbps Ethernet Interface (Ethernet Connector)
Power Requirements
3-pin IEC Input, Fuse
90-240VAC, 50-60Hz < 40W
Dimensions
Height: 44mm (1.75inch) 1U
Depth: 170mm (6.75 inches)
Width: 482mm (19 inches)
Weight
Net Weight: 2.2kg
Shipping Weight: 3.4kg
Due to continuous product improvement, the above parameters may vary slightly.
Related Products
Product Message
*Reminder: Please fill in the information accurately and maintain smooth communication. We will contact you as soon as possible.